IBM System/23 Datamaster: Difference between revisions
Added memory board picture |
No edit summary |
||
| Line 1: | Line 1: | ||
== Hardware Description == |
|||
=== RAM Memory === |
=== RAM Memory === |
||
| Line 32: | Line 35: | ||
The System/23 has a dedicated diagnostics port. It is controlled by a single 8255 by using its port B, whereas ports A and C have no relation in function; for this reason it is deduced that port B is working in mode 0, without handshaking of any sort. This fact is confirmed by the eight data lines which conform the data port being directly connected only to port B and the remaining four signals are for supplying power to the probes. |
The System/23 has a dedicated diagnostics port. It is controlled by a single 8255 by using its port B, whereas ports A and C have no relation in function; for this reason it is deduced that port B is working in mode 0, without handshaking of any sort. This fact is confirmed by the eight data lines which conform the data port being directly connected only to port B and the remaining four signals are for supplying power to the probes. |
||
| ⚫ | |||
After finding the pinout of the diagnostics port a simple probe containing a led per data line was built, and it showed a count when booting. Removing the RAM board(s) caused the count to stop at "00000100" (4 in decimal), which corresponds to a memory check test procedure of PID 1200. With those facts it was deduced that the port was outputting a two-digit hex code which was written just before the start of a test routine and would stop when the error was considered critical. |
After finding the pinout of the diagnostics port a simple probe containing a led per data line was built, and it showed a count when booting. Removing the RAM board(s) caused the count to stop at "00000100" (4 in decimal), which corresponds to a memory check test procedure of PID 1200. With those facts it was deduced that the port was outputting a two-digit hex code which was written just before the start of a test routine and would stop when the error was considered critical. |
||
For most cases it is not necessary having the probe, as the same values that are outputted through the service port are also written in the video memory, displaying the passed tests and the errors encountered. However, as the same tests that check the video display controller are the same routines that initialize it, all the tests made before the initialization cannot be seen in the screen until passed. In case some of them failed the screen would not be initialized and therefore the results wouln't be seen. For this reason the probe is still needed. |
For most cases it is not necessary having the probe, as the same values that are outputted through the service port are also written in the video memory, displaying the passed tests and the errors encountered. However, as the same tests that check the video display controller are the same routines that initialize it, all the tests made before the initialization cannot be seen in the screen until passed. In case some of them failed the screen would not be initialized and therefore the results wouln't be seen. For this reason the probe is still needed. |
||
| ⚫ | |||
[[Category:Computers of IBM]][[Category:Computers of the United States of America]] |
[[Category:Computers of IBM]][[Category:Computers of the United States of America]] |
||
Revision as of 08:49, 13 May 2024
Hardware Description
RAM Memory
RAM in the Datamaster is completely contained in one to two boards complementary to the motherboard and are attached through a card-edge connector of 36 pins each. This facilitates the removal and placement of memory cards into the system and grants the possibility of fast repair and extension of the computer. There are two memory slots, and at the same time official memory boards were produced in two sizes: 32KB and 64KB respectively. This led to five possible official configurations.
| Feature board | Option board | Total |
|---|---|---|
| 32KB | None | 32KB |
| 32KB | 32KB | 64KB |
| 64KB | None | 64KB |
| 64KB | 32KB | 96KB |
| 64KB | 64KB | 128KB |
Still, it is known that the official maximum of 128KB is just the maximum for the earlier models of 5322, as later revisions could address up to 256KB by configuring some jumpers in the motherboard. This is possible as the bank control register is implemented with a 74LS670, which is 4 bits wide, giving 16 pages of 16KB each. Additionally, there is a non-banked page which is used among other things as the display memory. For this reason the actual theorical maximum memory for a System/23 is 272KB. Still, it has been hinted that some clones of the system exist and that those expand the width of the page register to eight bits, giving the theorical maximum to 4112KB to them.
The memory boards contain one or two TMS4132 arrays of 9 memories each. Having nine units per bank allows them to have a data byte width of data plus a ninth bit for parity. Both because of the rareness of the format of the TMS4132 and the replacement of the official reference led for years to believe that IBM soldered the memories in piggyback to cope with failure rates when in reality it was a feat of Texas instruments to sell them directly soldered after manufacture of both dies. This kind of memory contains a 16KB bank per package and both packages have a slight difference of the pinout to not have conflict with /CAS and /RAS.
Memory is subject to many diagnostics tests, some of which are considered critical and could prevent the system from successfully IPL, giving the impression of a completely dead computer whereas only the memory could be failing. It has also been tested that the computer won't boot if no memory board is present at the "feature" socket.
Diagnostics port
The System/23 has a dedicated diagnostics port. It is controlled by a single 8255 by using its port B, whereas ports A and C have no relation in function; for this reason it is deduced that port B is working in mode 0, without handshaking of any sort. This fact is confirmed by the eight data lines which conform the data port being directly connected only to port B and the remaining four signals are for supplying power to the probes.
After finding the pinout of the diagnostics port a simple probe containing a led per data line was built, and it showed a count when booting. Removing the RAM board(s) caused the count to stop at "00000100" (4 in decimal), which corresponds to a memory check test procedure of PID 1200. With those facts it was deduced that the port was outputting a two-digit hex code which was written just before the start of a test routine and would stop when the error was considered critical.
For most cases it is not necessary having the probe, as the same values that are outputted through the service port are also written in the video memory, displaying the passed tests and the errors encountered. However, as the same tests that check the video display controller are the same routines that initialize it, all the tests made before the initialization cannot be seen in the screen until passed. In case some of them failed the screen would not be initialized and therefore the results wouln't be seen. For this reason the probe is still needed.